#define TOOLCHANGE_FIL_SWAP_RETRACT_SPEED 3600 // (mm/m) If material enters the hotend more quickly, then more heat will need to be added to maintain energy balance. #endif #define PROGRESS_MSG_EXPIRE 0 // (ms) Amount of time to retain the status message (0=forever) "#define X_HOME_DIR -1 #define DEFAULT_STEPPER_DEACTIVE_TIME 120
I'm confused. Specify a large enough delay so the servo has enough time to complete a full motion before deactivation.With this option servos are powered only during movement, then turned off to prevent jitter. #define INVERT_Z_STEP_PIN false #endif #define BED_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor #define PREVENT_LENGTHY_EXTRUDE #define INVERT_E2_DIR false #if ANY(SWITCHING_TOOLHEAD, MAGNETIC_SWITCHING_TOOLHEAD, ELECTROMAGNETIC_SWITCHING_TOOLHEAD) Wir sind ein echter Schweizer 3D Druck Shop aus dem Raum Zürich und haben seit mehr als 5 Jahren Erfahrung mit dem Drucken, Handel und Vertrieb von 3D Druck Produkten. It knows the properties of the 3D printer, like the dimensions or heating settings. It seems to me that after I drop in my pre-configured files and make further changes that MY changes would be stored in a data file somewhere other than configuration.h so that when a new Marlin version is released, configurator would be able to pull the new release, apply all of MY unique changes and then be ready for a fresh build. Allowed values: 2400, 9600, 19200, 38400, 57600, 115200, 250000.Enable the Bluetooth serial interface. #define HOTEND3_RESISTANCE_25C_OHMS 100000 // Resistance at 25C With this option simply connect the X2 stepper to the first unused E plug.Dual X-Carriage has three different movement modes, set with Adds control for any solenoid attached to an extruder. Marlin can be used to turn the spindle on and off. CoreXY uses a special belt arrangement to do XY motion, requiring a little extra maths. The Software is ditributed with “beerware license” as in “free as in beer” and all donations will be used to pay for the components. If the temperature difference between sensors exceeds Set how far from target the chamber can be and still be considered ok.These parameters help prevent the printer from overheating and catching fire. #define HEATER_3_MINTEMP 5 Vendors are strongly discouraged from using Settings that can be changed and saved to EEPROM are marked with When you change saveable settings in the configuration files and re-flash, the new values don’t take effect right away. #define MIXING_VIRTUAL_TOOLS 16 // Use the Virtual Tool method with M163 and M164 #define LED_USER_PRESET_RED 255 // User defined RED value #define TEMP_SENSOR_CHAMBER 0 Once up to speed the fan can drop back to the set speed. GitHub is home to over 50 million developers working together to host and review code, manage projects, and build software together. #define SPINDLE_LASER_POWERUP_DELAY 50 // (ms) Delay to allow the spindle/laser to come up to speed/power
If you require a value over 10, this could indicate a problem.High Temperature Thermistors tend to give poor readings at ambient and lower temperatures. Define a FIL_RUNOUT#_PIN for each. The E motor also reverses direction for the second filament. #define TOOLCHANGE_PARK_XY_FEEDRATE 6000 // (mm/m)
//#define PAUSE_PROBE_DEPLOY_WHEN_TRIGGERED // For Manual Deploy Allenkey Probe//#define PROBING_HEATERS_OFF // Turn heaters off when probing//#define WAIT_FOR_BED_HEATER // Wait for bed to heat back up between probes (to improve accuracy)//#define PROBING_FANS_OFF // Turn fans off when probing//#define PROBING_STEPPERS_OFF // Turn steppers off (unless needed to hold position) when probing//#define DELAY_BEFORE_PROBING 200 // (ms) To prevent vibrations from triggering piezo sensors#define X_ENABLE_ON 0 #define NEOPIXEL_BRIGHTNESS 127 // Initial brightness (0-255) //#define DOUBLECLICK_FOR_Z_BABYSTEPPING // Double-click on the Status Screen for Z Babystepping.//#define EXTRA_LIN_ADVANCE_K // Enable for second linear advance constants#define LIN_ADVANCE_K 0.22 // Unit: mm compression per 1mm/s extruder speed Should be slower than load feedrate. #define TEMP_SENSOR_AD595_GAIN 1.0 [C°] #endif #define HOTEND2_PULLUP_RESISTOR_OHMS 4700 // Pullup resistor This can be pretty fast. Search. Marlin3dPrinterTool is a open-source software that helps you configure and test your 3D printer. Either the Z height can continue to raise/lower by the established tilt of the nearest grid box (best when most of the bed was probed), or it can follow the contour of the nearest edge (the default). #define ULTIPANEL_FEEDMULTIPLY // Encoder sets the feedrate multiplier on the Status Screen #define Y_HOME_BUMP_MM 5 #define SWITCHING_TOOLHEAD_X_SECURITY { 90, 150 } // (mm) Security distance X axis (T0,T1) // Feedrate (mm/m) for the first approach when double-probing (MULTIPLE_PROBING == 2)// Feedrate (mm/m) for the "accurate" probe of each point#define Z_PROBE_SPEED_SLOW (Z_PROBE_SPEED_FAST / 2)